Regulator Parts

Bungee cord for a variety of uses including regulator necklaces, forearm mounts for your compass or computer, or wing bladder compression.  Sold by the foot, change the quantity for the continuous length you need. 4mm (5/32") diameter.  

Secure your backup regulator to your scuba BCD to ensure it's there if you need it.  Features: One end clips to your backup regulator hose, securely attached and screwed in place The other half clips to a d-ring on your BCD The two sides are...

Zip ties for securing a mouthpiece to a scuba regulator or a snorkel. No bump design eliminates sharp end usually found on traditional zip ties. Qty 1 = Package of 10 zipties.  

Super stretchy silicone octo holder is perfect for keeping your backup scuba regulator close at hand and easy to find. One end loops around your octo mouthpiece. The other end attaches to d-ring on your BCD. Bright yellow color is easy to see...

Water activated marker lights turn on when they come in contact with water and turn off when they are dried off. Features: Total life is 500 hours which far exceeds most marker lights on the market Perfect to mark your tank or marker buoy while...

Don't let your gauges drag along the bottom, damaging delicate coral reef or stirring up a muddy bottom. Features: Attaches between your gauges and your BCD d-ring Quick release clips between 2 bungee loops One bungee loop attaches to your gauge...

The best dive bag you will ever own! Carry it on the plane with your regulators and then unzip to turn it into a mesh duffel to carry everything onto the dive boat. The perfect travel bag and boat bag. Features: Regulator compartment is large enough...

Fully padded regulator bag protects your scuba regulators and other small items like a dive computer. Features: Shoulder strap attaches to reinforced d-rings for extra strength and durability Padded holder for gauges or computer Interior velcro...

Small and lightweight signalling device that attaches to your scuba BCD power inflator hose. Features: Emits loud signal both in air (on the surface) and in water (underwater) Above water, the horn will be heard from 1 mile away Underwater it can...

Effortlessly clip and un-clip your backup regulator as it hangs conveniently on your BCD. The plug helps eliminate free flows and any sand or other debris from getting inside the mouthpiece.

Reduce jaw fatigue and soreness with the mouldable mouthpiece for your snorkel or scuba regulator.  Material: Mouldable siliconeColors: BlackUse: Scuba regulator or snorkelStyle: Hot-water mold and scissor-trim the bite tabs for a custom...

Holds your primary or backup scuba regulator conveniently and comfortably just below the chin for easy access in an emergency. The necklace measure approximately 60cm/24inches circumference or 19cm/7.5inches in diameter.

Quick, spin-on adapter for a DIN regulator first stage to adapt to yoke/k-valve scuba tank.

Protect your DIN regulator first stage from dust, water, and other unwanted contaminants. Features: Made from plastic Attached nylon cord lanyard Fits all 200 bar and 300 bar DIN

Mini retractor for streamlining your gauge console or other scuba gear. Features: High-force 12-inch steel line Secure with the velcro wrap on your gauge Use the keyring to attach directly to your gauge. Dimensions: 2 x 1.5 x .75 inches

Routes your regulator hose under the right arm instead of over the should for more comfortable diving. Often used on the backup regulator to improve hose routing. Installs between the second stage and regulator hose. Chromed brass construction, factory...

Bungee cord for a variety of uses including regulator necklaces, forearm mounts for your compass or computer, or wing bladder compression.  Sold by the foot, change the quantity for the continuous length you need. 5mm diameter.

Made with high quality stainless steel, this handy repair tool fits in your save-a-dive kit or tool box easily. Perfect for quick repairs at the dive site or on the boat. Features: Spanner wrench for regulator first stage Hose wrench for various...

Holds your primary or backup scuba regulator conveniently and comfortably just below the chin for easy access in an emergency. The necklace measure approximately 79cm/31inches circumference or 25cm/10inches in diameter.

Replacement orings for DIN regulator first stage. Package of 5. This item qualifies for FREE SHIPPING*! (*Shipped letter mail with Canada Post. Regular shipping policies apply when combined with other items)

Convert a standard yoke first stage to a DIN first stage with the conversion kit. Works with Scubapro first stages (except MK5).

Protect the first stage of your diving regulators from dust, water, and contamination. Always replace your rubber dust cover when regulators are not in use or hooked up to a scuba tank.

The Scubapro Sport Bag 9 is perfect for carrying your scuba regulators and other gear. The bag has less padding compared to other regulator bags making it less bulky and perfect for when you want to keep your regulators separate while packed in your...

Fits first stage low pressure port - 3/8" to 3/8". Can be used to as an elbow for attaching a low pressure hose to a low pressure port on the first stage of a regulator.

Features: Install between low pressure hose and regulator second stage for quick connect and disconnect Perfect for removal of full face scuba masks or second stage regulator for storage and transport Equipped with a lock down screw to prevent...

Adds an additional high pressure port to your scuba regulator first stage for use with your scuba gauges or dive computer transmitter. Features: Chromed brass construction and viton orings High pressure only - max 5000 psi Cleaned for use with up...

Connection: 9/16"-18 UNF 2A to 3/8"-24 UNF 2B x 2. Can be used to attach 2 low pressure hoses to one low pressure port on first stage regulator.

Add to your scuba diving regulator to help reduce jaw fatigue and increase comfort. Features: Install between low pressure regulator hose and second stage Reduce hose torque on the second stage leading to increased comfort and reduced jaw fatigue...

Connection: 3/8"-24 UNF 2A to 3/8"-24 UNF 2B x 3. Can be used to attach 3 low pressure hoses to one low pressure port on first stage regulator.

Fits first stage high pressure port - 7/16" to 7/16".  Can be used to as an elbow for attaching a high pressure hose to a high pressure port on the first stage of a regulator.

Thread Adapter for scuba diving regulator.  Click on images for specifications of each type of fitting.   Type #2 - 3/8-24 UNF female to 9/16-18UNF male (an example of use for this adapter would be to connect 2 LP regulator hoses...

Protect your DIN regulator with the aluminum regulator dust cover cap. Features: Screws on easily to your DIN first stage Protect from dust, debris, and water while not in use Made of aluminum

Install between low pressure hose and second stage regulator. Can be used to stop airflow in the event of a free flow. 

Reduce jaw fatigue, soreness and issues with TMJ with the Seacure moldable mouthpiece for your snorkel or scuba regulator. Hot-water mold and scissor-trim the bite tabs for a custom fit, Latex free. SeaCure 1 Fits regulator size...

Routes your regulator hose under the right arm instead of over the should for more comfortable diving. Often used on the backup regulator to improve hose routing. Installs between the second stage and regulator hose. Chromed brass construction, factory...

This adapter is used to extended the High Pressure port on a first stage regulator. This can allow you to add a wireless air transmitter to a HP port on a first stage with limited space.

Used to convert the Aropec RG1002 first stage regulator from yoke to DIN.

All the essential gear for anyone that is purchasing or already owns their own scuba regulators.  Features: Regulator Storage Bag - Keep your regulators safe during storage or travel. Perfect size for a carry-on as your "personal item"...